Clik here to view.
CY8CKIT-048 and Photodiode Project
Forums: PSoC 4 ArchitectureI'm starting a new project which I think the Analog Coprocessor Kit would be a good kit to use for the initial testing. I'm looking at replacing the detector (datasheet...
View ArticleWhat does place PSoC 4 and PSoC3/5 in different buckets
Forums: PSoC 4 ArchitectureIt is hard to ignore that there is a consistent grouping of the PSoC 3 and PSoC 5 architectures. I do not recall ever seeing a document title with 3/4, 4/5 or 3/4/5...
View Articlesqrt function
Forums: PSoC 4 Architecturei have done Project -> Build Settings -> Linker -> General and adding the letter "m" into Additional Libraries.i got error rodata will not fit in region rom. rom...
View ArticleUSBFS - component not found -
Forums: PSoC 4 ArchitectureI was working my way through AN-73503, USB HID Bootloader earlier today. I followed their instructions to delete the default Device Descriptor root. I then imported the...
View ArticleClik here to view.
PWM Glitch when Dimming
Forums: PSoC 4 ArchitectureHello,I have a working code for a capsense button project. If the user presses the capsense button, the LED will slowly get brighter and when the button is pressed again the...
View ArticleClik here to view.
LinearSlider definition & Parameter undefined
Forums: PSoC 4 ArchitectureHello; I try to follow or reproduce the video: How to Create a PSoC Android BLE App.I include the CapSense CSD Module, the BLE Module, and the digital outputs. After...
View ArticleClik here to view.
Problem with using ESP826 with PSOC 4
Forums: PSoC 4 ArchitectureHello,I have problem with my project. I connect ESP as follows: vcc - P4.vddgnd - GNDRX - TX (P0.5)TX - RX (P0.4)firstly I had a problem with a restart of the Wi-Fi module...
View ArticleFOC Sensorless BLDC
Forums: PSoC 4 Architecture Hi,Is the sample code(example) only suits for speed control of motor? Can it also be used for torque control of motor? Are they both different source codes?can anyone please...
View ArticlePSOC 4 with ESP8266 nad HC-SR501
Forums: PSoC 4 ArchitectureHello,I have problem with mentioned devices. HC-SR501 motion sensor is always high when there is also a Wi-Fi module ESP8266 connected to my board. What could be the issue?
View ArticleDuty Cycle Measurement
Forums: PSoC 4 Architecturei am using a demo board of CY8CKIT-043 with very low resources (32 macro-cell) could you write a short code the do the folowing: input= digital INPUT, random behaviouer of 0...
View ArticleCan I assign the function components in the code
Forums: PSoC 4 ArchitectureHello,Can I assign those function components in the code dynamically?e.g.,sometime I want to take P3.0,P3.1 as UART,sometime take as I2C in the one C code file,is it...
View ArticleCY8CKIT-044 Powering from Vin
Forums: PSoC 4 ArchitectureI have a CY8CKIT-044 that I can power using USB; however, when I try to power the kit using J7 (Vin, Gnd), the board will not power up. I have tried 12v-5v/3a converted, 9v...
View ArticleClik here to view.
LCD_Char_PrintString() doesn't show anything on 16x2
Forums: PSoC 4 Architectureplease helpproject is attached. when i connect the programmer and program the chip or put in debug mode LCD_Char_PrintString() works.if i removed the programmer and connected...
View ArticleFind digital input interrupt source
Forums: PSoC 4 ArchitectureHi,I have digital input component (SW) configured for 3 inputs (One, Two, Three) sharing the same falling edge interrupt isr_SW. Physically they all connected to P0[0],...
View ArticleClik here to view.
CE211252 Ambient Light Sensor Example Warnings
Forums: PSoC 4 ArchitectureI was experimenting with the example project from the CY8CKIT-048 development board. I've got some odd warnings that I can't seem to find information about:Opamp...
View ArticleBootloading using UART v2.50
Forums: PSoC 4 ArchitectureHi, my question is if I can use the UART v2.50 module with the Bootloader instead of using the SCB module in PSoC 4. I understand I must use the "Custom Interface" option in...
View ArticleMotor driver is activated but couldn't rotate and only vibration is able to hear
Forums: PSoC 4 Architecture Hi,In FOC sensorless BLDC motor control when I started the Bridge driver is activated (I tested) but the current is also supplying to the stator coils but the motor...
View ArticlePower Consumption of PSOC-4 BLE
Forums: PSoC 4 Architecturehi, i have been using psoc-4 til now and i started work on psoc-4 ble by today.first i have changed thermocouple input software directly from psoc-4 to psoc-4 ble.i have...
View ArticleClik here to view.
how to save current in deepsleep mode?
Forums: PSoC 4 ArchitectureHi,i'm using the CY8C4024LQI-S412 controller on a test board. With a simple program (switch a LED on and off in an ISR) i want to test the power consumption of the UC.In deep...
View ArticleClik here to view.
"Unable to find a solution for the analog routing" error, when using two IDACs
Forums: PSoC 4 ArchitectureHi So I'm trying to use two of the built in IDACs, for higher resolution, but it gives me the error:"apr.M0003:Unable to find a solution for the analog routing" A screenshot...
View Article